-
Find in Members
Find in Videos
Find in Channels
This website uses cookies to ensure you get the best experience on our website.
To learn more about our privacy policy Click herePrivacy Preference
Categories
19 pages found.
Map View
Grid View
List View
-
August 23, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe public lighting(CLASSICLEDLIGHT) https://www.classicledlight.com/
is an indispensable part of our life. It dispels the darkness at night and brings us light. It is a "companion" who accompanies... moreThe public lighting(CLASSICLEDLIGHT) https://www.classicledlight.com/
is an indispensable part of our life. It dispels the darkness at night and brings us light. It is a "companion" who accompanies us home at night. Street lights rely on light energy as a power source to realize independent public lighting. Since street lights use intelligent automatic lighting, how can street light manufacturers configure controllers to achieve good public lighting when installing street lights in order to ensure the quality of public lighting?
In order to ensure the normal operation of the entire public lighting system, the controller should be able to ensure that the battery components are not overcharged or voted on and damaged under any conditions, and have control, control, voice control, temperature compensation, lightning protection and reverse polarity protection functions at the same time. In addition, the controller is responsible for monitoring the charging state of the battery module and managing the charging process including the opening and closing of the load, so that the battery module can make full use of energy and prolong the service life. When configuring the controller, it can limit the charging voltage to prevent overcharged battery modules, close the load to prevent discharge, and the controller can prevent excessive current. When the temperature is too high, the controller can automatically open or close the load or components. Overvoltage, the load can shut down the load.
Due to the non-contact control technology adopted by the controller, it has advanced control functions, is especially suitable for street light and photovoltaic power generation control through automatic load switching, and has various protection functions. Therefore, when installing street lights, street light manufacturers can only achieve good public lighting by reasonably configuring the controller.
Click Led Public lighting https://www.classicledlight.com/
to learn about more information. less -
August 20, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe installation method of Solar led street light(CLASSICLEDLIGHT) https://www.classicledlight.com/product/led-solar-street-light/
is very important. The correct way is to carry out the installation... moreThe installation method of Solar led street light(CLASSICLEDLIGHT) https://www.classicledlight.com/product/led-solar-street-light/
is very important. The correct way is to carry out the installation and construction with reference to the road lighting installation code. It is also necessary to combine with the specific situation of the installation site to develop a correct and reasonable installation method of solar LED street light. For the lack of professional knowledge of the installation personnel. There may be installation errors.
1. Installed in a lot of obstructions
The working principle of the solar LED street light is that during the day, the battery board absorbs the sun in the battery. In the evening, the battery converts the sunlight into electric energy and supplies the street light. At this time, the light will be on. But then again, solar panels can absorb sunlight to store electricity. If the streetlights are installed in a lot of shelters, such as being blocked by many trees or blocked by buildings, they will not absorb sunlight. Therefore, the light will not light or the brightness will be dark.
2. Installed near other light sources
Solar LED street lights have their own control system that recognizes daylight and darkness. If another power source is installed next to the solar LED street light, when the other power source is lit, the system of the solar LED street light will be considered to be daytime, and it will not light up at this time.
3. The solar panel is mounted under other obstructions
Solar panels are made up of multiple strings of cells. If one of the strings is not exposed to sunlight for a long time, then the battery is useless. The same is true. If a solar LED street light is installed in a place, there is a certain obstruction in that place that blocks a certain area of the solar panel. This area cannot be converted into electricity by long-term exposure to sunlight. The battery in that area is also equivalent to a short circuit.
4. Mount the lights on both sides of the road, the solar panels are tilted face to face
It should be very common to install lights on both sides of the road, but there will also be a problem that the sun will only rise from the east. If the street light on one side is facing east and the street light on one side is facing west, then there is There may be one side facing away from the sun, which will not absorb the sun, because the direction is not right. The correct way to install it is that the solar panels face up and the solar panels on both sides absorb the sunlight.
5. Solar LED street light is placed indoors for charging
Install solar LED street lights in the carport or in other indoor spaces, as this facilitates lighting. However, if it is installed indoors, the solar LED street light will not function, because its battery panel is completely blocked, it can not absorb sunlight, no sunlight can be converted into electric energy, and it can not be illuminated. If solar LED street lights are to be installed indoors, the solar panels and lights can be installed separately, so that the panels are charged outdoors and the lights are illuminated indoors. Of course, we can also use other lighting in indoor lighting.
If you are ready to upgrade to a more efficient lighting system, for more information, please click Led street lights Manufacturers https://www.classicledlight.com/
. less -
July 14, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewDespite advances in logistics, just-in-time production processes, and distribution networks, warehouses are still an important component of industrial, commercial and consumer goods supply and... moreDespite advances in logistics, just-in-time production processes, and distribution networks, warehouses are still an important component of industrial, commercial and consumer goods supply and distribution networks. In this new environment, warehouse operators are under pressure to continuously reduce costs and help manufacturers and shippers store and deliver raw materials and finished products at the lowest possible price. Warehouse cost savings are usually achieved by reducing indirect costs. The most direct way to reduce these costs is to use more efficient public lighting(CLASSICLEDLIGHT) https://www.classicledlight.com/
.
Public lighting accounts for 50 to 75 percent of the warehouse's electricity consumption. According to a recent measure, if all warehouses in the United States switch to more efficient public lighting equipment, they will save a total of more than $12 billion in annual electricity bills. Gaowan metal halide lamps or high-pressure sodium lamps are currently the most common form of public lighting in warehouses, but warehouses are transitioning to light emitting diodes to achieve the cost savings estimated by these recent measures.
If you are ready to upgrade to a more efficient lighting system, for more information, please click Led Public lighting https://www.classicledlight.com/
. less -
July 7, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewSports fans may notice some changes taking place in outdoor stadiums and arenas where their favorite teams play. The old metal halide and high-pressure sodium lights in these facilities are being... moreSports fans may notice some changes taking place in outdoor stadiums and arenas where their favorite teams play. The old metal halide and high-pressure sodium lights in these facilities are being eliminated and replaced by new public lighting(CLASSIC) https://www.classicledlight.com/
. Fans can see new public lighting, for example, in the home stadiums of the National Football League's Houston Texans and Arizona Cardinals. The NFL is probably the most well-known league to use public lighting, but universities and other public outdoor sports venues are also following the trend of light emitting diodes. When considering the advantages of light emitting diodes over traditional public lighting, it is easy to understand why light emitting public lighting is changing outdoor sports.
A typical professional or university outdoor football field holds 10 to 15 football matches every year. Football stadiums have little or no revenue because they are not used. Stadium operators need to find ways to make the best use of these facilities and save operating costs to justify the existence of stadiums and the capital expenditure for their construction. For stadium operators, public lighting is a key component to solve this problem.
Click Led Public lighting https://www.classicledlight.com/
to learn about more information. less -
June 4, 2019 - posted by xiu umin, 1 like, 0 followers, 1 member, 0 comments, 1 viewIt is the responsibility of the mould designer to provide adequate circulation within the Table Mould(FURNITUREMOULD) https://www.furnituremould.com/product/chair-table-stool-mould/
. Usually, the... moreIt is the responsibility of the mould designer to provide adequate circulation within the Table Mould(FURNITUREMOULD) https://www.furnituremould.com/product/chair-table-stool-mould/
. Usually, the simplest system is a system that drills longitudinally through a template. However, this is not necessarily the most efficient method for a particular mould.
However, when drilling is used for the circulation of the coolant, these should not be too close to the indentation (eg, less than 16 mm) as this may result in significant temperature changes on the indentation, resulting in moulding problems.
The layout of the circuit is often complicated because the runners cannot be placed too close to any other hole in the same template. It can be recalled that the template has a large number of holes or grooves to accommodate the ram, the guide post, the guide sleeve, the sprue bushing, the insert, and the like. The degree of safety in positioning in the direction of flow adjacent to another orifice depends to a large extent on the depth of drilling of the desired flow pattern. When drilling deep runners, the drill tends to deviate from its prescribed route. The rule that is often applied is that for holes up to 150 mm deep, the flow should not be less than 3 mm of any hole. For deeper flow patterns, this margin is increased to 5mm.
Click Chair Mould https://www.furnituremould.com/product/chair-table-stool-mould/
to learn about more information. less -
April 16, 2019 - posted by xiu umin, 1 like, 0 followers, 1 member, 0 comments, 1 viewFurniture Mould(FURNITUREMOULD) https://www.furnituremould.com/
consists of two or more stamps that can be custom moulded to different parts. Polymers are being successfully applied in furniture... moreFurniture Mould(FURNITUREMOULD) https://www.furnituremould.com/
consists of two or more stamps that can be custom moulded to different parts. Polymers are being successfully applied in furniture moulds. As with any alternative polymer, they must be balanced to flow into unique components. Most components should be filled evenly and evenly. Otherwise, uneven packaging can occur; many components will be over-wrapped and subjected to high stresses, causing warpage, and other components will be packaged or not completely filled. Note: Furniture moulds should be avoided as much as possible because it is difficult to obtain a balanced flow. If a furniture mould is required, the flow should be balanced by changing the diameter of the flow path, not the gate size.
The polymer has excellent gloss and is ideal for extracting furniture moulds. Keep in mind that polishing a smoother surface than required for polishing will only increase the cost of the furniture mould. In most cases, extremely polished surfaces can hinder ejection if the vacuum is typically applied with minimal or no drafting. Where there is no vacuum, the polished surface usually bounces better.
Reduce the possibility of creating a vacuum during ejection. Repair furniture mould surface texture can be used to hide weld lines, flow marks, gate blush, sink scars and scratches. There are hundreds of standard modes to choose from. Basically, anything that can be drawn in black and white can be used as the basis for a texture pattern.
It is important to determine the texture pattern early in the design process in order to incorporate the appropriate draft angle and contour directly into the part.
Click Air Cooler Mould https://www.furnituremould.com/
to learn about more information. less -
March 31, 2019 - posted by xiu umin, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe result of some things caused by the accident. Errors in the installation of Household Product Mould(FURNITUREMOULD) https://www.furnituremould.com/product/daily-necessities-mould/
continue to be... moreThe result of some things caused by the accident. Errors in the installation of Household Product Mould(FURNITUREMOULD) https://www.furnituremould.com/product/daily-necessities-mould/
continue to be produced in troubled machines, and continued operation of household products mould that have begun to squeak or scream will cause damage. If the operation is allowed to continue without ending the problem, the household product mould that refuses to be normally closed or opened will be damaged, or the mould will not be ejected normally. An alert and well-trained foreman can hear trouble when passing through the moulding room. Mould damage of the above type is not limited to the printing shop. Tool room technicians failed to tighten the screws through incorrect mould assembly, leaving metal shavings, abrasive dust or polishing abrasives on or near the sliding surface to contribute their share.
Fatigue is the main cause damage in household products mould, which results in the destruction of household products mould that are subjected to maximum stress while prolonged circulation. This usually happens if it will occur after 100,000 and 300,000 moulding cycles. In a multi-cavity mould, the same components as the first broken component can last for a limited longer period of time. Fatigue can be manifested in components that are subjected to compressive loads as well as in torque, tension or bending components.
Thermal shock has a questionable contribution to the deterioration of household products mould. As far as our analysis is concerned, unless the rapid heating and cooling of the household product mould is part of the cycle, there is usually only a small effect compared to hydraulic and mechanically induced stresses. Household product mould operate at higher temperature ranges - 500 to 800 °F, which deteriorates faster; this is a historical issue with die-casting moulds.
Click Daily Necessities Mould https://www.furnituremould.com/product/daily-necessities-mould/
to learn about more information. less -
February 10, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewFrom employees to customers, everyone has the right to enjoy peace of mind in a safe and secure shopping environment, especially in the parking and garage areas. In addition to preventing certain... moreFrom employees to customers, everyone has the right to enjoy peace of mind in a safe and secure shopping environment, especially in the parking and garage areas. In addition to preventing certain hazards, there are many reasons why Led Public lighting(CLASSIC) https://www.classicledlight.com/
has become so popular.
For commercial establishments, customers may be at risk of personal injury when there is insufficient or insufficient lighting in the parking lot and sidewalk areas. In order to reduce risk and prevent such problems (sometimes with litigation), business owners should do their utmost to ensure proper outdoor LED public lighting in these areas.
When you consider it, well-lit areas often reduce criminal activity, personal injury, and physical injury to visitors. This is because proper LED public lighting and other functions can help illuminate dark areas so that visitors can conduct business without any of these unfortunate accidents. In fact, municipalities have recognized the benefits of using LED public lighting facilities in these areas.
If you are ready to upgrade to a more efficient lighting system, for more information, please click public lighting https://www.classicledlight.com/
. less -
January 25, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe public lighting(Classic) https://www.classicledlight.com/
guidelines in the UK and many other countries are currently based on suspicious evidence. That's why the Public Lighting Research Group... moreThe public lighting(Classic) https://www.classicledlight.com/
guidelines in the UK and many other countries are currently based on suspicious evidence. That's why the Public Lighting Research Group at the University of Sheffield conducted a research project to understand the relationship between lighting and the sense of security after dark, and to improve the evidence on which the public lighting guidelines are based.
In a recent experiment, we asked people to walk on some streets in Sheffield at night and assess their sense of security. We also require these people to walk and rate the street on the same day to create baseline security measures and consider the deviations that may occur if the safety rating is taken only after dark.
The difference in safety levels between day and night walks tells us about the lighting on that street, the smaller the difference between day and dark levels, and people feel safer because of lighting. We compared the different ratings of the participants to the lighting metrics on each street, including the average illuminance (the amount of light falling on the street surface) and the uniformity (the degree to which the illumination is evenly distributed).
If you are ready to upgrade to a more efficient lighting system, for more information, please click Led Public lighting https://www.classicledlight.com/. less -
January 23, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe main purpose of public lighting(Classic) https://www.classicledlight.com/
is to produce fast, accurate and comfortable visibility at night. This visibility can protect, promote and encourage... moreThe main purpose of public lighting(Classic) https://www.classicledlight.com/
is to produce fast, accurate and comfortable visibility at night. This visibility can protect, promote and encourage vehicle and pedestrian traffic. When providing good visibility through illumination, efficient nighttime use of large investments in roads and motor vehicles can be made. Therefore, the correct use of public lighting as a surgical tool can bring economic and social benefits to the public, such as:
1. Reduce nighttime accidents, accompanied by human suffering and economic losses.
2. Help the police protect and enhance personal security.
3. Promote traffic flow.
4. Promote business and use public facilities at night.
In order to drive a vehicle on a paved road with reasonable confidence, speed and safety, the driver must visually determine the following:
1. The road ahead has no defects and obstacles at a reasonable distance.
2. The location of the lane or lane edge.
3. The location and meaning of the traffic control device and the signs that affect the "road rules."
4. Move the current position and future route of the object on or near the road.
5. The current position of the driver's own vehicle relative to its immediate destination, other objects, and the predetermined turning position.
Darkness poses a greater hazard to users of streets and highways because it reduces the distance they can see. The nighttime fatal accident rate on unlit roads is about three times the daytime rate. This ratio can be reduced when properly fixed illumination is installed, as these illumination systems reveal an environment that exceeds the range of the vehicle's headlights and improve the glare of oncoming vehicles by increasing the level of adaptation of the eye. Preventive measures such as public lighting and highways are economically practical and can make the cost of the community lower than accidents caused by insufficient visibility.
Click Led Public lighting https://www.classicledlight.com/
to learn about more information. less -
January 22, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewRoad safety Information: public lighting(Classic) https://www.classicledlight.com/
and road safety This raises concerns about the relationship between driver perceived safety and actual safety... moreRoad safety Information: public lighting(Classic) https://www.classicledlight.com/
and road safety This raises concerns about the relationship between driver perceived safety and actual safety levels, as well as how the driver behaves in both situations. If the driver feels a better level of safety due to lighting, and therefore behaves more dangerously when their vision is not significantly improved, does this lead to an increase in risk, not just a reduction in brightness?
The latest evidence concludes that there is no evidence of reduced light and nighttime collisions throughout England and around the world. However, previous studies have concluded that there are positive safety benefits. The survey shows that the public is in favor of public lighting as a way to improve road safety and, if so, improvement in certain areas.
For economic and environmental reasons, some organizations may wish to reduce the amount of lighting. However, it is necessary to provide a safety reason for lighting. In some cases, reducing the quality of the lighting may not increase the risk of an accident. However, there is a danger that unremoved removal or reduction in quality actually increases the accident and its severity. Therefore, location-based traffic and accident evidence should be evaluated when considering the removal or dimming of lights. The accident rate should be monitored to ensure that sacrificing lighting quality does not excessively increase the risk. An increase in risk may eventually lead to loss of life.
Click Led Public lighting https://www.classicledlight.com/
to learn about more information. less -
January 18, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewSeveral cities use HPS for public lighting(Classic) https://www.classicledlight.com/
. Although it produces orange light, the color is closer to "natural light" than LPS. If people like to use white... moreSeveral cities use HPS for public lighting(Classic) https://www.classicledlight.com/
. Although it produces orange light, the color is closer to "natural light" than LPS. If people like to use white light in an area, LEDs and metal halides are the most popular choices. LED public lighting is ideal for outdoor lighting because you can dim it according to your requirements. You can easily turn them off or reduce the intensity to suit your needs. In this way, we can not only save energy, but also reduce the amount of light pollution emitted at night.
With the introduction of LED luminaires and LED bulbs, there are now more ways to help our environment and wildlife. If we know how to use this lighting correctly, we can overcome many of the negative effects that undermine our natural flow. Once people have decided on the outdoor lighting they like, they can use the appropriate fixtures to replenish the bulb. Although there are hundreds of different types of fixtures that can be used to meet different needs, only a few fixtures are beneficial to protect wildlife and the surrounding environment.
In addition, light colors are also important. In addition to having the right lighting and lighting, you can choose the right lighting color. A sufficient amount of blue light is present in both the metal halide lamp and the LED. Since blue light illuminates the night sky more than other types of lights, it is important to limit the percentage of blue light that the bulb emits into the surrounding environment. Studies have identified a definitive relationship between blue light exposure and harmful effects on human health and wildlife. Therefore, according to IDA's suggestion, it is beneficial to use light with a color temperature below 3,000 Kelvin.
Click Led Public lighting https://www.classicledlight.com/
to learn about more information. less -
January 15, 2019 - posted by xiu xiu, 1 like, 0 followers, 1 member, 0 comments, 1 viewIn order to emphasize the importance of environmental protection in the future for sustainable development, April 22 has been designated as Earth Day. Not only is this a short publicity, but it also... moreIn order to emphasize the importance of environmental protection in the future for sustainable development, April 22 has been designated as Earth Day. Not only is this a short publicity, but it also encourages people from all over the world to implement the concept of protecting the environment. There are many problems with pollution. Obviously air pollution and water pollution. These also broke through our beautiful global environment, causing many species to be extinct. In our daily lives, we can use Solar led street light(Classicledlight) https://www.classicledlight.com/product/led-solar-street-light/
, floodlights and other solar equipment to reduce dependence on fossil fuels. Burning fossil fuels produces many environmentally harmful substances such as sulfur dioxide and carbon particles. These substances are the cause of acid rain. Therefore, if we reduce the use of energy from coal or oil, we do not need power plants to increase energy production to reduce emissions of carbon and other harmful substances.
To encourage people to install and use solar panels and other renewable energy sources, many regions have used “selling electricity” or the on-grid tariff policy to induce citizens to install solar equipment on the roof. The energy is first stored in the battery and then sold to the power company. Of course, these tenants can also use electricity directly as street lights and outdoor floodlights.
But is the price of electricity repurchase impressive? The answer is yes. On average, the cost of repurchasing solar power is about 25% to 40% higher than that of ordinary electricity. While this "selling electricity" program is considered effective, we should focus on those who may abuse it and buy a lot of solar panels, which will eventually lead to waste.
Click Led street lights Manufacturers https://www.classicledlight.com/
to learn about more information. less -
December 28, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewIn the past, the Paddy Husker(LIANGGONG) https://www.china-zjlg.com/product/rubber-roller-husker/
equipment has the disadvantages of aging models and poor quality of the milled rice. The new paddy... moreIn the past, the Paddy Husker(LIANGGONG) https://www.china-zjlg.com/product/rubber-roller-husker/
equipment has the disadvantages of aging models and poor quality of the milled rice. The new paddy husker complete sets of equipment can easily solve the disadvantages of the previous equipment. Before the paddy husker machine completes the equipment, the users need to The equipment performs load debugging work, which is the premise to ensure the safe use of the equipment, but the method that can be used for load debugging work is different. Which methods can be adopted for the load debugging work of the paddy husker machine complete equipment?
Load debugging method for paddy husker complete equipment:
Load debugging method a thickness of the flow: the material is spread over the second layer of the screen surface and moves in a wavy "boiling" state, and the lower layer is preferably half of the transparent glass observation window.
Load debugging method 2 The size of the reverse wind: control the anti-air blow, so that the cross and wheat form a clear dividing line (the stone area is generally about 5cm), the stone is normal, and the stone contains the compound requirement, which is the normal working state. The distance between the anti-drying damper and the screen surface is about 15-20mm.
Load Debugging Method Three Suspension Speed ??Test: The granules beat or feel good on the sieve surface.
Click Paddy Separator https://www.china-zjlg.com/product/paddy-separator-machine/
to learn about more information. less -
December 20, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewWhen the temperature of the flour produced by the Rice Polisher(LIANGGONG) https://www.china-zjlg.com/product/polishing-machine/
equipment is relatively high, the gap of the grinding roller should... moreWhen the temperature of the flour produced by the Rice Polisher(LIANGGONG) https://www.china-zjlg.com/product/polishing-machine/
equipment is relatively high, the gap of the grinding roller should be adjusted. If it is found to be the cause of the wear of the grinding roller, it should be repaired or replaced in time. Rice polisher equipment should pay special attention in the summer to grasp the heat dissipation of the machine. The reason for this situation in rice polisher equipment is that the steering of the main shaft is incorrect and the screen is worn.
In addition, electrical safety is also very important. Due to the high temperature season, the heating of rice polisher equipment will be more serious. Tripping of electrical equipment is a common thing, so it should be checked and patrolled in time, and the abnormal situation will be solved immediately, and the aging will be replaced in time. Electrical equipment and wiring will completely solve the safety hazard.
Summer is also a season of high failures, pay attention to the noise that occurs during use:
1. The flour unit will have a squeaking sound during the operation, which is the need to add grease to the bearing lack of oil.
2. If the flour machine has a "beep" sound, this is the sound of the ball turning, which is generally caused by lack of oil and needs to be refueled.
Click Rice Whitener https://www.china-zjlg.com/product/rice-whitener-machine/
to learn about more information. less -
December 6, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewIn simple terms, the Rice Destoner(LIANGGONG) https://www.china-zjlg.com/product/destoner-machine/
machine is a mechanical product that uses mechanical force to peel and whiten brown rice. If the... moreIn simple terms, the Rice Destoner(LIANGGONG) https://www.china-zjlg.com/product/destoner-machine/
machine is a mechanical product that uses mechanical force to peel and whiten brown rice. If the rice destoner machine is not ready for use before starting the machine, it will directly use the machine, in order to avoid the deterioration of the complete equipment of the rice destoner, save the repair costs, ensure the stable operation of the equipment, and work efficiently, the company's technical staff here today introduces in detail the preparatory work that should be done before the start of the rice destoner complete equipment.
Preparation for the rice destoner complete set before starting the machine:
1. The complete set of rice destoner machine equipment should be installed smoothly before starting. Check whether the components are normal, whether the parts and their connections are loose or not. The transmission belts are suitable for tightening. The belts must be flexible. Pay attention to the lubrication of each transmission part. In the case, the above parts can be started after the check is normal.
2. Remove the debris in the rice to be milled (such as stone, iron, etc., can not have too long stones, iron), so as to avoid accidents. Check if the dryness and wetness of the rice meets the requirements, then insert the rice plug into the bucket and put the rice into the bucket to be beaten.
Click Paddy Cleaner https://www.china-zjlg.com/product/vibrating-cleaning-screens/
to learn about more information. less -
November 21, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe operation method is to pay attention to before starting the Paddy Husker(LIANGGONG) https://www.china-zjlg.com/product/rubber-roller-husker/
machine. Always check whether there are loose parts... moreThe operation method is to pay attention to before starting the Paddy Husker(LIANGGONG) https://www.china-zjlg.com/product/rubber-roller-husker/
machine. Always check whether there are loose parts in each part of the machine. Check whether the gap between each part meets the requirements. Try to prevent unnecessary damage. Check the switch. After waiting for the machine to run for 4 minutes, if there is no problem, you can use it directly. At the beginning, you should slowly process it. While paying attention to the changes of the paddy husker machine, you can correct the problem in time, for the problematic part make adjustments.
The price of the rice mill complete sets of equipment is also unattainable from the initial. This price trend reflects the trend of universalization, popularization, popularization, and practicality of paddy husker machines. The rice milling machine completes the miniaturization of a set of radical mechanical equipment for processing rice, which is convenient for household use. It is a complete set of light and small paddy husker machine equipment, from traditional large-scale industrial rice grinding equipment and rice milling machine complete equipment. Technology, operation, convenience and other aspects have breakthrough technological innovations, so that household paddy husker machine has gradually become recognized by the public, into the new household equipment of thousands of households.
At the same time, the separation of rice and rice is carried out, and the paddy husker machine complete equipment can be processed into rice in one time. Prevent mixing together. The water content of the processed rice is relatively large. Such processing will directly affect the quality of the rice produced, and the use efficiency of the memory machine will be different from the tone in other applications.
Click Paddy Separator https://www.china-zjlg.com/product/paddy-separator-machine/
to learn about more information. less -
November 15, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewWhen the Paddy Separator(LIANGGONG) https://www.china-zjlg.com/product/paddy-separator-machine/
is wholesale, it is the basis to find the manufacturer. Therefore, we have to have more knowledge when... moreWhen the Paddy Separator(LIANGGONG) https://www.china-zjlg.com/product/paddy-separator-machine/
is wholesale, it is the basis to find the manufacturer. Therefore, we have to have more knowledge when we choose the equipment, so we can have outstanding performance in terms of quality. Therefore, we still have to have More attention, so that we can have a good performance in the service level, and then can be satisfied in the reliability.
Pay attention to the manufacturer's quotation, and provide reference for customers to purchase equipment, which will enable consumers to have more gains in product selection. Only when the quality is better, can the user be satisfied. After all, it will bring more help to the user, and it needs to attract enough attention.
Strong equipment vendors will be able to provide customers with quality services, so we can't blindly determine when making product selection. Choosing to purchase equipment through wholesale means not only can be more prominent in the price advantage, but also has a good guarantee in quality, so it is advisable to choose a wholesaler for the purchase of equipment.
The company reserves the secondary and senior management, production and technical professionals to supply high-quality products and excellent service based on the scientific management and latest technology. It sticks to the tenet of “quality foremost, faith as essential”to insistently respond customers with high-quality products and perfect after service.The sales networks of the company are covered all over China as well as South American, South East Asia, Africa etc.The company cordially welcomes all of you to visit us for the win-win future.
Click Paddy Husker https://www.china-zjlg.com/product/rubber-roller-husker/
to learn about more information. less -
November 12, 2018 - posted by gong liang, 1 like, 0 followers, 1 member, 0 comments, 1 viewThe pneumatic Rice Huller(LIANGGONG) https://www.china-zjlg.com/product/mlgq51-semi-pneumatic-rice-huller.html
machine is divided into stone by the air separation device consisting of the screed,... moreThe pneumatic Rice Huller(LIANGGONG) https://www.china-zjlg.com/product/mlgq51-semi-pneumatic-rice-huller.html
machine is divided into stone by the air separation device consisting of the screed, the sifting screen, the woven screen, the ventilating hood and the air valve after the grain passes through the rubber roller. That is, the same air duct is used for the valley and the stone, so that the grain can pass through the machine and complete various processing such as glutinous rice, grading, and stone removal. The main features of the equipment: high degree of automation, high shelling rate, large output, compact structure, stable operation, low noise, is the first choice for rice processing equipment with a daily output of more than 100 tons.
Pneumatic rice huller machine features
1. The automatic logic control device action sequence can realize the automatic tightening of the incoming material and the automatic unloading of the material;
2. The pressure between the rolls is controlled linearly by the barometer, the output is digitally adjusted, and the pressure and output adjustment are concise and intuitive;
3. Using the color selection machine vibration feeding technology, using the vibration frequency of the inverter controller feeder, the flow rate is continuous and stable;
4. Double sided synchronous belt transmission, accurate transmission speed ratio, flexible center distance, no lubrication, high efficiency. It has the advantages of three kinds of transmissions: belt, chain and gear. It runs smoothly and has low noise during operation.
Click Rice Grader https://www.china-zjlg.com/product/rice-grader-machine/
to learn about more information. less
Locations on MyWorldGo
Loading ... 
