Bad Influences of Aluminum Magnet Wire Are Introduced

More from yuu xin

  • Do You Want to Know Aluminum Magnet Wire Applications?
    0 comments, 0 likes
  • Know Aluminum Magnet Wire of Your Home
    0 comments, 0 likes
  • We Introduce Separating Factors of Aluminum Magnet Wire
    0 comments, 0 likes

More in Politics

  • Drug De Addiction in Hospital in Chennai
    0 comments, 9,636 views
  • Where You Can Use Rock Carpet
    0 comments, 3,699 views
  • Impotence - Advice on Impotence and the Treatments Available
    0 comments, 2,639 views

Related Blogs

  • Wise Techniques For Real Property Investment
    0 comments, 0 likes
  • Zopiclone buy Online UK to cure insomnia and other sleep problems
    0 comments, 0 likes
  • Women can reignite their lost interest in intercourse with Ladygra 100 mg
    0 comments, 0 likes

Archives

Social Share

Bad Influences of Aluminum Magnet Wire Are Introduced

Posted By yuu xin     May 6    

Body

The aluminum magnet wire is a controversial subject in the real estate world. I often have clients ask questions like, “Is aluminum wiring safe?” or “Does it need to be replaced?”. My short answer is yes it is safe, and no it does not need to be replaced. However, I need to elaborate on those answers, as aluminum wiring requires special considerations.


Photo Credit: Daniel Smith

The Myth

I often hear people say that aluminum wiring is not allowed or has been “outlawed” for use in residential construction. This is not true. It is still very much allowed when installed properly.

Traditionally, copper has been (and still is) the preferred conductor since electricity’s inception in the late 1800’s. It wasn’t until the 1960’s, at the height of the Vietnam War era, that aluminum wiring began to be used in American homes. Copper prices were sky high as it was being used to make munitions and other products for military use. Home builders had to find an affordable alternative. That alternative was aluminum.

Copper is Better

It is well known that copper is a better electrical conductor than aluminum. The manufacturers and rating agencies knew this and required aluminum wire be sized one gauge larger than copper wire to carry the same current. Where a branch circuit to a light fixture is traditionally ran with 14 gauge copper, it would have to be ran with 12 gauge aluminum. The smaller the the gauge, the larger the wire.

The Problems

Problems began to arise a short time after aluminum wire became widely used. Issues included lights flickering, cover plates on switches and receptacles would be warm to the touch, and burnt wire insulation. These were all caused by the aluminum wire overheating for several reasons we will look at below.

Softness

Aluminum wire is softer that copper which made it much more susceptible to cuts and nicks when removing insulation to make connections. When an area of a wire is damaged, that place becomes a hot spot that will overheat.

Wire Creep

When electricity passes through a wire, it heats up. When metal heats up, it expands, and, consequently. it contracts when it cools down. Aluminum has a higher expansion rate than copper. The expansion and contraction cycle due to heating and cooling would cause what is referred to as “creep.” When connected to outlets not approved for use with aluminum wire, the wire would literally creep out from under the terminal screw holding the wire down. This created a loose connection that would overheat.

Oxidation

As with any metal, aluminum will oxidize, more commonly known as rusting. The difference between copper and aluminum is that the rust formed on copper is still a good electrical conductor. The rust that forms on aluminum does not conduct electricity well at all. It creates resistance that will cause overheating.


Outlets damaged by loose aluminum wiring

The Solution

The problems noted above all occurred at the connection points like those receptacles, switches, light fixtures and at the main panel. The way to prevent these issues was, and still is, to use special connectors approved for use with both copper and aluminum. There were receptacles, switches, wire nuts, breakers and other electrical devices designed for this purpose. They should be marked or labeled with one of three markings: CO/ALR, AL-CU, or CU-AL.

Building inspectors were not common at the time when aluminum wiring was being installed. As a result, aluminum wiring was installed in many homes without connectors approved for use with aluminum. This is where the problems occurred and are still occurring today.

Stay tuned for my next post in which I will discuss more issues associated with aluminum wiring, insurance companies, and what to do if your house has aluminum wiring.

If you are interested in aluminum winding wire, welcome to send us messages immediately!

Comments

0 comments