DOME Fiber Closure Usage Details I

More from fiberclosure top

  • History Fiber Cartridge Technology
    0 comments, 0 likes
  • We must be flexible in managing inline closures
    0 comments, 0 likes
  • Introduction of Fiber Optic Connector Closure Plant (Waterproof Measures)
    0 comments, 0 likes

More in Politics

  • Norton antivirus account login
    3 comments, 31,555 views
  • Liquidity Locking Made Easy
    0 comments, 31,125 views
  • Drug De Addiction in Hospital in Chennai
    1 comment, 19,351 views

Related Blogs

  • In April 2012, Jagex redefined the rule
    0 comments, 0 likes
  • The 2oz Bottle Provides Peace Of Cosmetic Cream Jar
    0 comments, 0 likes
  • Injection Plastic Mold Could Be A Good Choice
    0 comments, 0 likes

Archives

Social Share

DOME Fiber Closure Usage Details I

Posted By fiberclosure top     November 29, 2018    

Body

Green Telecom's products are mainly related to communication. The main products are DOME Fiber Closure , Fiber Optic Splice Closure, Inline Closure, Fiber Closure and the like.

Fiber preparation
1. Remove the cable sheath (if any, remove the shield and armor) and then remove each of the wraps to expose the loose tube. For details, please follow the standard method recommended by the fiber optic cable manufacturer. The preparation length is 3m.
2. Clean the loose tube and the core sheath with detergent, remove the excess filling sleeve, and sand the cable with a sandpaper provided to a length of 150 mm.
Cable installation
1. Select the seal ring with the smallest inner diameter according to the outer diameter of the cable and place the two seal rings on the cable.
2. Place the fiber optic cable into the corresponding access hole.
3. Connect shield and ground.
4. Wrap a self-adhesive sealing tape between the two sealing rings so that the sealing tape is wound flush with the outer diameter of the sealing ring to form a cable sealing end.
5. Press the sealed end of the cable into the hole of the cable.
6. Pass the hose clamp through the cable rib fixing seat and the cable core bracket, fix the cable to the base of the joint box, and tighten the hose clamp until the hose clamp is tightened.
7. Put a nylon cable tie on the cable and cut off the excess length.
8. The remaining unused cable holes should be sealed with a plug. The sealing tape is also wound on the plug and is required to be the same as 5.2.4.
9. Wrap the reinforcing member around the countersunk screw of the splice tray holder and press it tightly.

Fiber Optic Connection / Cable Connector Kit

1. Prepare the fiber for 1.5 turns after the disk is placed, and then wrap the remaining fibers in the box.
2. Use a single-core buffer tube for the single-core fiber tray and a ribbon buffer tube for the ribbon-shaped fiber tray. Nail with a nylon cable tie at the entrance of the splice tray.
3. Dock two (belly) optical fibers according to the specified method. The connector is snapped into the slot of the fusion unit. The remaining length should be coiled in the disk.
4. Cover the splice tray and press it into place.
5. According to the different capacity required of the joint box, determine the number of disks to be superimposed on the welding plate. The superimposed type of the welding plate must conform to the card-in welding unit of the fiber connector and check and maintain requirements. Each two welding plates are superimposed, and the rubber can be folded into six holes to respectively catch the three convex twists on the upper and lower plates; four rubber folding pages, two symmetric positions on each side of the disk, such as superimposed five For the welding plate, the two-layer disk and the three-layer disk are buckled according to the above method, the three-layer disk and the four-layer disk are buckled, the four-layer disk and the five-layer disk are buckled, and so on, and the five disks are stably stacked together. . When it is necessary to view or maintain the welding condition of a certain layer of the disk, as long as the two folding sheets of the upper layer of one side of the disk are removed, the welding plate can be opened like a page.

Click here to learn more about Fiber Optic Splice Closure .

Comments

0 comments